Friend, this video is gonna save lots of folks butts as long as you keep it up. You just helped me provide my 2yo daughter with a hot bath tonight. Many thanks!
Thank you just when I thought I was going to give a service technician on a Saturday night I found this video and it worked out just like it did in your video.Thank you.
The water heater shut off about two days ago while I was out of town. Found your Video and now the kids and I can take hot baths once again!!! Thank you so much!!
I am new to this type of control valve. Gas had been turned off in the house and they could not get the water heater to light. Your video was what I needed to get it to light. Thank you very much...
Oh thank you thank you thank you, you made a very bad day a lot less bad. woke up today and somebody sideswiped my car, my dryer is out well... it's louder than a jackhammer. Then I went to wash some dishes and there was no hot water, I was thinking great! found this video and I don't have to replace my water heater at least. 🙏
Thank you so much for this! With this video's help, I got the pilot light going again and I have never felt so much like my own superhero (by following your instructions! Lol) Thank you!!!
Thank you!! Fixed my issue so l got afew questions? Is this something to indicate failure? Just out of warranty purchased 4/24/2018. Also been curious for awhile so what powers the blinking LED light?? A battery? Replacement needed? Lifespan if a battery?
I don’t think it indicates a mechanical issue, however, I’m not an expert on water heaters. The blinking light is powered by the thermopile that is located near the pilot light. Once it’s heated by the pilot light, it converts that heat to electricity. Thanks for commenting!
Hi Stephen thanks for the vid it helped alot. I noticed i had 9 blinks... its a chamber sensor warning, do you know what that means? I did the reset and it returned to blue and reignited. I am just curious as to what it is that messed up. I got mine in 2022 october.
@@rvalle11 I think that means the sensor is going bad and needs replaced. I have never encountered this issue, but I would think that your water heater should still be under warranty. I would call customer service and ask them what you should do. Thanks for commenting!
My heater can show red or blue indicator lights. I was able to re-light the pilot using your instructions and then the light flashed blue, once every second or so. I assume this means everything is OK?
What’s it mean if I can light the pilot light, pilot light stays on till I remove finger from pilot light knob and the blinking light never comes on? Ty!
I’m not an expert on this but it may be that the thermopile or thermocouple is bad. Have you tried holding the pilot button for 30 seconds after the pilot lights?
After waiting for 10seconds, I pressed the pilot button in and had to click the ignition button every second for 30 seconds until the light started to flick and then I turned to “hot” and it reset
@@CougarsSaluki Yes. Sometimes you have to keep hitting the igniter until it lights. I got lucky and the pilot lit on the first click. You did it correctly! Good job!
I did all that and in the last step when you turned it to hot, it clicks but the flame stays the same and does not increase. It is a new unit. Any ideas what the issue is?
@@mariogallardomusic I’m sorry I don’t. If the burner doesn’t light there’s something else wrong. It should be under warranty so I would call the place you purchased it from.
I cant even get my status light to turn on no matter how many times I hit the ignite button while holding pilot down...I may have a different issue, maybe a bad igntitor box?
@@KazzamGameHaven The status light won’t come on until the pilot lights. If you’re following the directions on your gas valve to re-light the pilot and it doesn’t light, you need to call a professional.
@@DiyGuy50 I ended up getting mine lit. Under the panel cover you take off to see if the pilot light is lit to the right theres 2 wires. I disconnected both of those and plugged them back in. Water heater started right up no problems after that!
@@freshtelovision If your pilot doesn’t light, there is something else wrong. It could be that the igniter isn’t working, the thermocouple is bad.., so you better call a plumber.
You're supposed to look in the sight glass for the pilot to light. Once lit you don't need to hit the ignitor anymore. You continue to hold the pilot button down until the light starts to flash. Once it's flashing that means the thermocouple is warmed and the burner is ready to light.
@@joebojanic1905 That is correct. I heard the pilot light after the first press of the igniter. But, if you release the control button prematurely, the pilot goes out because the thermocouple hasn’t got hot. Thanks for sharing.
@@blissfullycoiled1114 when you press the control button it releases gas and pressing the ignitor repeatedly should light the pilot. If it doesn’t, turn the control to off and call an expert.
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
damn this video saved me so much money! our guy kept bullshitting us!. charging us and not even fixing shit! 🙏🏻 God bless you sir
God bless you for sharing! Made my day!
Thank you so much, Stephen! I followed your instructions and restarted my water heater in 30 seconds...
Friend, this video is gonna save lots of folks butts as long as you keep it up. You just helped me provide my 2yo daughter with a hot bath tonight. Many thanks!
@@poundkake13 That’s awesome! You made my day! Thank you!
Thank you just when I thought I was going to give a service technician on a Saturday night I found this video and it worked out just like it did in your video.Thank you.
@@johnanderson2046 You’re welcome! Glad it worked for you!
I'm so glad to find this! My wife wanted a new water heater NOW! It all worked exactly like you said. Thank you.
@@mrideal2348 ❤️❤️❤️
I am so glad I could help! Thank you for sharing!
Thank you so much for the information... retired and on a very small budget. God bless you!!
Thank you! God bless you!
@@DannyH-t8h I’d say you’re back in business! Did you hear the burner ignite?
The water heater shut off about two days ago while I was out of town. Found your Video and now the kids and I can take hot baths once again!!! Thank you so much!!
@@calvinchapple Awesome! Thanks for letting me know!
I am new to this type of control valve. Gas had been turned off in the house and they could not get the water heater to light. Your video was what I needed to get it to light. Thank you very much...
@@chuckbrown6275 You’re welcome!
Oh thank you thank you thank you, you made a very bad day a lot less bad. woke up today and somebody sideswiped my car, my dryer is out well... it's louder than a jackhammer. Then I went to wash some dishes and there was no hot water, I was thinking great! found this video and I don't have to replace my water heater at least. 🙏
@@phillips91682ify You’re very welcome! Glad I could help!
Thank you so much for this! With this video's help, I got the pilot light going again and I have never felt so much like my own superhero (by following your instructions! Lol) Thank you!!!
@@brandim.7702 Awesome! You are welcome! So glad I could be of some help!
Thanks for the clear direction! On my way to a hot shower!
Happy I could help! Thanks for commenting!
Very helpful video 👍
Thank you!
Thanks for the video. Got the pilot light lit. I’m wondering why it went out though
@@Hellbound330 The temperature might have been set a little too high.
This worked perfectly for me. Thank you so much!
You’re welcome! Thanks for sharing!
Thanks for the help!💕👏🏽👏🏽👏🏽
@@jenniferdenise6167 You’re welcome!
God bless you. I had this problem fixed in ten minutes.🎉😂👏🏾👏🏾👏🏾
@@apsvend Thank you! God bless you!
This was so helpful. Thanks!
@@EvetteCollins You’re welcome!
Thanks for the tips I got my water heater back on track
Awesome! Thanks for sharing!
Thank you! Mine did the exact same thing. Very helpful video!
@@michaelhayden6936 Great! Thanks for letting me know!
Thank you!! Fixed my issue so l got afew questions? Is this something to indicate failure? Just out of warranty purchased 4/24/2018. Also been curious for awhile so what powers the blinking LED light?? A battery? Replacement needed? Lifespan if a battery?
I don’t think it indicates a mechanical issue, however, I’m not an expert on water heaters. The blinking light is powered by the thermopile that is located near the pilot light. Once it’s heated by the pilot light, it converts that heat to electricity. Thanks for commenting!
Thank you so much for this video!!! You saved me from probably spending a few hundred dollars on a repair person!!!!
You’re welcome!
God bless you brother, thank you 🙏🏻
@@cualessonsusdeseospidanlo6616 You’re welcome! God bless you too!
you are the MANNN!!! ran like a champ!
Awesome! Thanks for sharing!
This is awesome! Thank you it worked.
You’re welcome! Thanks for sharing!
Hi Stephen thanks for the vid it helped alot. I noticed i had 9 blinks... its a chamber sensor warning, do you know what that means? I did the reset and it returned to blue and reignited. I am just curious as to what it is that messed up. I got mine in 2022 october.
@@rvalle11 I think that means the sensor is going bad and needs replaced. I have never encountered this issue, but I would think that your water heater should still be under warranty. I would call customer service and ask them what you should do. Thanks for commenting!
This video really helped me out a lot! Thanks
You’re welcome!
My heater can show red or blue indicator lights. I was able to re-light the pilot using your instructions and then the light flashed blue, once every second or so. I assume this means everything is OK?
@@paulajenkins6978 Is your gas valve a Honeywell?
@@DiyGuy50 Yes, it's Honeywell. Similar to yours except the status light can flash red or blue. The info card says flashing blue means normal.
@@paulajenkins6978 👍
Thank you very much.
Yes this helped!!!
You're welcome!
It’s took exactly one minutes but I got it, thanks for your advise
@@Efrain279 you’re welcome!
This video worked! Only thing is my light is blinking red.
@@bd4177 Great! A blinking red light is normal for some models . Thanks for sharing!
What’s it mean if I can light the pilot light, pilot light stays on till I remove finger from pilot light knob and the blinking light never comes on? Ty!
I’m not an expert on this but it may be that the thermopile or thermocouple is bad. Have you tried holding the pilot button for 30 seconds after the pilot lights?
very useful thank you
@@wussrocker You’re welcome!
Much appreciated brother 🙏🏻
@@kylewilliams1439 You’re welcome! Thanks for sharing!
After waiting for 10seconds, I pressed the pilot button in and had to click the ignition button every second for 30 seconds until the light started to flick and then I turned to “hot” and it reset
@@CougarsSaluki Yes. Sometimes you have to keep hitting the igniter until it lights. I got lucky and the pilot lit on the first click. You did it correctly! Good job!
Thanks so much, it worked
@@debrasuebinzley8509 Awesome! Thanks for sharing!
It works! Thanks so much!
@@flyingslipper3909 You’re welcome!
Hell yeah thanks man from colorado
Any time!
I did all that and in the last step when you turned it to hot, it clicks but the flame stays the same and does not increase. It is a new unit. Any ideas what the issue is?
@@mariogallardomusic I’m sorry I don’t. If the burner doesn’t light there’s something else wrong. It should be under warranty so I would call the place you purchased it from.
I cant even get my status light to turn on no matter how many times I hit the ignite button while holding pilot down...I may have a different issue, maybe a bad igntitor box?
Yes. If your pilot doesn’t light, you’re either not getting a spark or gas and it must be another issue.
Thank you friend
@@kingsleyhoard6681 you’re welcome friend!
I tried to do it, I'm pressing and holding the pilot while clicking the button below it every 3 secs but light is not blinking.
@@noneofus6381 It may be something else. There are a number of reasons that you can’t light the pilot.
What if the status light doesnt come on even tho i cant get the pilot light lit, doesnt stay lit because the status light doesnt come on...
@@KazzamGameHaven The status light won’t come on until the pilot lights. If you’re following the directions on your gas valve to re-light the pilot and it doesn’t light, you need to call a professional.
@@DiyGuy50 I ended up getting mine lit. Under the panel cover you take off to see if the pilot light is lit to the right theres 2 wires. I disconnected both of those and plugged them back in. Water heater started right up no problems after that!
@@KazzamGameHaven Thats great! Thanks for letting me know!
I hold the pilot button light does not turn on. Help?
@@freshtelovision If your pilot doesn’t light, there is something else wrong. It could be that the igniter isn’t working, the thermocouple is bad.., so you better call a plumber.
What if mine isn’t blinking at all at any time?
@@DanielMcCarley That is how I found mine. ( not blinking). Have you tried resetting it?
You're supposed to look in the sight glass for the pilot to light. Once lit you don't need to hit the ignitor anymore. You continue to hold the pilot button down until the light starts to flash. Once it's flashing that means the thermocouple is warmed and the burner is ready to light.
@@joebojanic1905 That is correct. I heard the pilot light after the first press of the igniter. But, if you release the control button prematurely, the pilot goes out because the thermocouple hasn’t got hot. Thanks for sharing.
Both my neighbor and I did this and the status light is still not coming on.
@@loeserlegal Are you continuously pushing the igniter while depressing the control button and is your control button on pilot?
Thanks🎉
On his FIRST try with ONE hand?
Other videos say it takes DOZENS of attempts to get it lit.
@@dialecticalmonist3405 I got lucky, lol!😉😜
😅😅😅😅😅
I smell gas when I do it.
@@blissfullycoiled1114 when you press the control button it releases gas and pressing the ignitor repeatedly should light the pilot. If it doesn’t, turn the control to off and call an expert.
U are so slow
@@TOMsideways-nt6tx What’s the hurry?
I tried to do it, I'm pressing and holding the pilot while clicking the button below it every 3 secs but light is not blinking.
@@noneofus6381 if the pilot doesn’t light, there’s something wrong. Better call an expert.
Same here the pilot comes on but it doesn't flash the light
If your pilot doesn't light, there is something else wrong.
@@glasscleanercrew1285 There is something else wrong. Maybe a bad thermopile?
@glass literally said PILOT COMES ON BUT THE LIGHT DOESN'T FLASH